Banner MAXI-AMP Series Manuel d'utilisateur télécharger pdf

MODEL

OUTPUT LOGIC

CR3A

CR3B

CR5A

CR5B

105 to 130V ac, or

12 to 28V dc

210 to 250V ac, or

12 to 28V dc

timing func-

tions

210 to 250V ac, or

12 to 28V dc

105 to 130V ac, or

12 to 28V dc

SPST solid-

state contact for

switching AC

loads up to 250

V ac and up to

3/4 amp, plus

solid-state con-

tact for switch-

ing DC loads up

to 30V dc and up

to 50mA.

SUPPLY

VOLTAGE

ON/OFF

• Modulatedphotoelectricamplier,powersupply,

 outputrelay,andversatiletiminglogic(CR5

  models)inonecompact,stand-alonepackage

• 120or240Vacor12to28Vdcoperation;re-

quires onlytheadditionofBanner"100

Series"modulated  remotesensor(s)to

createacompletesensing  system

• CR5modelsareeasilyprogrammedforanyof12

 delay,one-shot,andlatchfunctions(singleordual

 timing);interrogationschemesarepossibleusing

 themodule'sauxiliaryinput

Printed in USA P/N 03452C4D

Model CR5RA shown

with SP100C sensor

MAXI-AMP

™

CRSeries

ModulatedAmplierModulesfor"100Series"Sensors

CR Series MAXI-AMPs combine power supply, modulated photo-

electric ampliﬁer, timing logic (in CR5 models) and output relay in a

single compact, cost-saving module. The integrated stand-alone design

saves both the expense of a separate control chassis and a substantial

amount of panel space. Several models are available, for either 120V

or 240V ac operation, and either with or without timing logic. Alte-

natively, any model may be powered by 12 to 28V dc.

CR Series modules are speciﬁcally designed for use with the popular

"100 Series" of Banner miniature sensors (page 3). Their rugged en-

capsulated design, slim ribbon-style connecting cables, and small size

make these sensors ideal for use in many situations previously considered

impractical or impossible. MAXI-AMP modules themselves are also

ruggedly built for dependable industrial duty.

CR Series MAXI-AMP modules contain the state-of-the-art Banner

custom-designed CMOS modulator/demodulator/ampliﬁer circuit, of-

fering high immunity to both ambient light and electrical interference

plus reliable sensor performance. All models have Banner's exclusive,

patented Alignment Indicating Device (AID™) system, which lights an

LED indicator whenever the sensor sees a "light" condition, and pulses

the LED at a rate proportional to the received light signal strength.

All CR Series modules are programmable for LIGHT or DARK operate

and either high or low hysteresis. Input response time may be set at

0.3, 2, or 10 milliseconds. The 10-millisecond response mode offers

enhanced immunity to electrical interference ("noise"), and also mini-

mizes optical "crosstalk" between adjacent sensors.

CR5 models include a versatile multi-function timing logic circuit which

is programmable for 12 of the most popular and useful delay, one-shot,

and latch functions. Each timing function has a choice of three time

ranges. Timing and sensitivity adjustments are accomplished via rugged

15-turn potentiometers for very accurate settings. CR Series circuitry

is designed to prevent false outputs on system power-up.

The output circuit for all CR Series modules is an SPDT 5-amp electro-

mechanical relay. Additionally, CR3 models have an NPN transistor

solid-state switch. The output may be programmed for either normally

open or normally closed operation. A solid-state relay is offered as an

option to the electromechanical relay (see below).

An auxiliary input is available on CR5 models for interrogation or reset

of the selected logic function (see example, page 4). Page 6 describes

the function of the auxiliary input for each logic mode. A dc power

supply is included for powering an additional self-contained dc sen-

sor.

MODEL

OUTPUT LOGIC

SPDT electro-

mechanical relay

(5 amp contact

rating)

ON/OFF

timing func-

tions

210 to 250V ac, or

12 to 28V dc

105 to 130V ac, or

12 to 28V dc

CR3RA

CR3RB

CR5RA

CR5RB

105 to 130V ac, or

12 to 28V dc

210 to 250V ac, or

12 to 28V dc

SPDT electro-

mechanical

relay, plus NPN

transistor solid-

state DC switch

SUPPLY

VOLTAGE

Read Personnel Safety Use WARNING, page 7.

CR Series modules are available with a solid-state relay which replaces the

electromechanical relay. This is actually two SPST solid-state contacts. One

contact will switch ac loads, and is rated at 250V ac maximum and 3/4 amps

maximum at 25 degrees C (derated to 1/2 amp at 50 degrees C). The other

solid-state contact will switch dc loads of up to 30V dc and up to 50 milliamps.

Both contacts are isolated from the MAXI-AMP power supply.

Solid-stateOutputOption

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - CRSeries

MODELOUTPUT LOGICCR3ACR3BCR5ACR5B105 to 130V ac, or 12 to 28V dc210 to 250V ac, or 12 to 28V dc12timing func-tions210 to 250V ac, or 12 to 28V dc105 t

Page 2 - GeneralizedHookup

SUPPLY VOLTAGE: ModelsCR3(R)A,andCR5(R)A: 105 to 130V ac, 50/60Hz (4 VA), or 12 to 28V dc* at 70mA. ModelsCR3(R)B,andCR5(R)B: 210 to 250V ac,

Page 3 - DIFFUSEModeSensors

SensorsforusewithCRSeriesModulatedAmplierModulesTemperature range for all miniature modulated remote sensors is 0 to 70 degrees C (+32 to 15

Page 4 - Powerforexternaldevices

PowerforexternaldevicesLogiclevelNPNoutput,CR3modelsThe AUXILIARY terminal (#9) of models CR3(R)A and CR3(R)B offers a logic-level NPN (curren

Page 5 - Factory settings shown at

A group of ten switches, located on the side of the module opposite the ampliﬁer program switches, is used to select the timing logic for the CR5 mode

Page 6

LIMIT: The output of the LIMIT function follows the action of the input, as it does with the ON/OFF function. However, an input signal which is long

Page 7 - TROUBLESHOOTING

7InstallationandTroubleshootingofCRSeriesMAXI-AMPMod-WIRING TO MODULE: Input, output, and sensor hookup to a MAXI-AMP module are accomplished u

Page 8 - MAXI-AMPSystem

MAXI-AMPSystem MountingandAccessoriesAfter the panel cutout has been completed and de-burred, slide the MAXI-AMP through the cutout and place one c