Printed in U
P/N 03416 Rev. )
Construction: Reinforced molded VALOX
®
housing, molded acrylic
lenses, o-ring and quad-ring gasketed components. Electronic components
are fully epoxy encapsulated. NEMA 1, 3, 4, 12, and 13.
Operating Temperature: -40 to +70°C (-40 to +158°F).
Sensitivity Adjustment: Easily accessible, located on top of the sensor
head beneath a watertight gasketed screw-cover. 15-turn clutched control;
rotate clockwise to increase sensitivity.
Alignment Indicator: Red LED on top of sensor head. Banner's ex-
clusive AID™ circuit (*US patent no. 4356393) lights the LED whenever
the sensor sees its own modulated light source, and pulses the LED at a
rate proportional to the strength of the received light signal.
False Pulse Suppression on Power-up: 100ms delay on power-
up.
Response Time and Repeatability: Specications to follow in indi-
vidual product descriptions are independent of signal strength.
General Specications
Sensitivity
Control
LED/AID™
Indicator
Rotatable
Sensor Head
Programming
Ring
Optional
Logic Module
Programming
Ring for Logic
Power Block
Output OFF
LED
Output ON
LED
Quick Disconnect (optional)
Conduit
Entrance
RWB4
Wi r i ng
Base
VALOX
®
is a registered trademark of General Electric Co.
Some MAXI-BEAM sensor heads: models RSBC, RSBDSR,
RSBLV, and RSBF (shown with bifurcated ber optic assembly
attached).
Banner MAXI-BEAM
®
sensors are highly versatile, self-contained, modular-
ized photoelectric sensing controls that are ideally suited to industrial en-vi-
ronments. The basic MAXI-BEAM is an ON/OFF switch consisting of three
modules (sensor head, power block, and wiring base) and a unique, patented,
rotatable "programming ring" that enables you to program your choice of
"light" or "dark" operate mode, sensing range, and response time.
MAXI-BEAM sensor heads have an easily-accessible multi-turn SENSI-
TIVITY control for precise adjustment of system gain. Interchangeable
sensor heads are rotatable in 90-degree increments and are available in
retroreective, diffuse, opposed, convergent, xed-eld proximity, and
beroptic sensing modes. Each sensor head also includes Banner's exclusive,
patented AID™ circuit (Alignment Indicating Device*), which features
an LED alignment indicator that lights whenever the sensor "sees" its own
modulated light source, and pulses at a rate proportional to the strength of
the received light signal.
A wide selection of MAXI-BEAM power block modules is available to
interface the sensor head to the circuit to be controlled. The plug-in design
of the wiring base enables easy exchange of the entire sensing electronics
without disturbing eld wiring.
Optional customer-installable logic modules easily convert the basic ON/OFF
MAXI-BEAM into either a one-shot or delay logic function control, with
several programmable timing ranges for each function.
MAXI-BEAM sensors are ruggedly constructed of molded VALOX
®
to
NEMA standards 1, 3, 4, 12, and 13, and have interchangeable molded
acrylic lenses. Modules simply snap and bolt together, with no interwir-
ing necessary. Module interfaces are o-ring and quad-ring sealed for the
ultimate in dust, dirt, and moisture resistance.
To order a MAXI-BEAM, follow these steps:
1) Select a sensor head module,
2) Select a power block module,
3) Select a wiring base,
4) Select a logic module (if needed),
5) Select accessories as needed (see Banner product catalog).
Sensor Head Modules (described in this data sheet, P/N 03416)
RSBE & RSBR
opposed mode r a n g e t o
300'
RSBESR & RSBRSR
opposed mode (short range; narrow beam) range to 15'
RSBLV retroreective mode range to 30'
RSBLVAG
retroreective mode (anti-glare lter) range to 15'
RSBD
long range diffuse proximity mode range to 5'
RSBDSR short-range diffuse proximity mode range to 30"
RSBCV visible red convergent mode, focus at: 1.5"
RSBC infrared convergent mode, focus at: 1.5"
RSBF infrared ber optic; for glass bers
RSBFV visible red ber optic; for glass bers
RSBEF & RSBRF
infrared ber optic opposed mode; for glass bers
RSBFP
visible red ber optic; for plastic bers
RSBFF50, RSBFF100
xed-eld proximity; sharp far-limit cutoff at 50 or 100
mm
Power Block Modules (see data sheet P/N 03418)
RPBT
10-30V dc; one sinking and one sourcing solid-state output
RPBT-1
10-30V dc; for use with RSBE, ESR, EF emitters (no output circuit)
RPBTLM
10-30V dc low-prole power block (requires no RWB4 wiring base)
RPBA
105-130V ac (50/60Hz); SPST solid-state output
RPBA-1
105-130V ac (50/60Hz); for use with emitter (no output circuit)
R2PBA
2-wire operation; 105-130V ac (50/60Hz); SPST solid-state output
RPBB
210-250V ac (50/60Hz); SPST solid-state output
RPBB-1
210-250V ac (50/60Hz); use with emitter (no output circuit)
R2PBB
2-wire operation; 210-250V ac (50/60Hz); SPST solid-state output
RPBU
12-250V ac or 12-30V dc; SPST solid-state output (ac or dc)
RPBR
12-250V ac (50/60Hz) or 12-30V dc; SPST E/M relay output
RPBR2
12-250V ac (50/60Hz) or 12-30V dc; SPDT E/M relay output
Wiring Base (see data sheet P/N 03418)
RWB4
4-terminal wiring base for all models (except RPBTLM)
Logic Modules (see data sheet P/N 03417)
RLM5
ON/OFF delay (both functions adjustable up to 15 seconds)
RLM8
DELAYED ONE-SHOT (delay and pulse adjustable up to
15 seconds)
MAXI-BEAM
®
Sensor Heads
(6 pages)
(179 pages)
(16 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels